Hydraulic Vane Pumps High Pressure Hydraulic Vane Pumps BD05 Series Rated capacity at 0 bar Maximum pressure Geometric displacement 1200 rpm 1500 rpm intermittent continuos Speed range Cartridge model ml/rev. (in3/r) l/min (gpm) l/min (gpm) bar (psi) bar (psi) rpm 45 142,4 (8.69) 170.7 (45.15) 213.6 (56.51) 240 (3500) 210 (3000) 400 - 2200 50 158,5 (9.67) 189.9 (50.25) 237.7 (62.88) 240 (3500) 210 (3000) 400 - 2200 52 164,8 (10.06) 197.5 (52.25) 247.2 (65.40) 240 (3500) 210 (3000) 400 - 2200 62 196,7 (12.00) 235.7 (62.36) 295.0 (78.04) 240 (3500) 210 (3000) 400 - 2200 66 213,3 (13.02) 255.6 (67.62) 319.9 (84.63) 240 (3500) 210 (3000) 400 - 2200 72 227,1 (13.86) 272.2 (72.00) 340.6 (90.11) 240 (3500) 210 (3000) 400 - 2200 Technical characteristics Fixed displacement vane pump, hydraulically balanced, with capacity determined by the type of cartridge used and the speed of rotation. The pump is available in 6 different displacements from 214 to 341 l/ min (from 56 to 90 gpm) at 1500 rpm and pressure 0 bar. General description P S Hydraulic fluids: antiwear petroleum base, synthetic fluid, water glycols and invert emulsions. Viscosity range / Viscosity index: with antiwear petroleum base, from 10 to 2000 cSt. (10 to 108 cSt. recommended). Other fluids from 18 to 2000 c.St. (18 to 108 c.St. recommended). Choose 30 c.St. for max lifetime. Viscosity index: 90° min. Filtration: to maintain contamination level to ISO 18/14 or NAS 1638 class 8. Filters: for the inlet, use strainer with mesh not less than 149 micron abs. (omit strainer with application requiring cold start or when using fire resistant fluids); for the return line - 25 micron abs. or better. Water contamination level: max 0.10% for mineral oil. With other fluids, max 0.05% Intermittent pressure: typically the working time permitted at such pressure is < 30% of the duty cycle. With duty cycles longer than 15 minutes, please contact the technical office of B&C Minimum inlet pressure (with mineral oil 10-65 c.St.): 0,8 bar abs. (3 psi abs.). In the biggest displacements of each series and with the highest speeds, is required an higher inlet pressure. Please consult the specific section for details. In case of tandem pump, supply the inlet port with the highest pressure requested among the pump stages. Operating temperature: with “anti-wear petroleum base” the permitted temperature is: from -18 to +100°C; with water glycol and “water in oil emulsion”: from +10 to +50°C; with synthetic fluid: from -18 to +70°C; with rapeseed and esters: from-20 to + 70°C. During cold start the pumps should be operated at low speed and pressure until fluid warms up to an acceptable viscosity for full power operation. Drive: direct and coaxial by means of a flexible coupling. Low axial and radial loads allowed. Consult specific section for more detail. 16 www.jbj.co.uk/vane-pumps.html #DriveLineHarmony
RkJQdWJsaXNoZXIy NzQyNjQ=